* Refer to the Caterpillar 10/10/20 Payload Policy for maximum gross machine weight limitations.
Engine
Engine Model
Cat® C27
Rated Engine Speed
1800 r/min
Gross Power - SAE J1995:2014
825 hp
Engine Power - ISO 14396:2002
812 hp
Net Power - SAE J1349:2011
768 hp
Net Power - SAE J1349:2011/ISO 9249:2007
768 hp
Peak Torque - Speed
1200 r/min
Net Torque
3148 ft-lb
Bore
5.4 in
Stroke
6 in
Displacement
1648 in³
Note (1)
Power rating applies at 1,800 rpm when tested under the specified condition for the specified standard.
Note (2)
Net power advertised is the power available at the flywheel when the engine is equipped with fan at minimum speed, air intake system, exhaust system, and alternator.
Note (3)
Advertised power is tested per the specified standard in effect at the time of manufacture.
Note (4)
• No engine derating required up to 3048 m (10,000 ft). • Meets U.S. EPA Tier 4 Final and EU Stage V emission standards.
Emissions
Meets EU Stage V emission standards.
Capacity - Dual Slope - 100% Fill Factor
Struck
42.7 yd³
Heaped (SAE 2:1)*
55.5 yd³
Note (1)
Contact your local Cat dealer for body recommendation.
Note (2)
*ISO 6483:1980
Capacity - Flat Floor - 100% Fill Factor
Struck
42.2 yd³
Heaped (SAE 2:1)*
55.2 yd³
Note (1)
Contact your local Cat dealer for body recommendation.
Note (2)
*ISO 6483:1980
Weight Distributions - Approximate
Front Axle - Empty
52 %
Front Axle - Loaded
34 %
Rear Axle - Empty
48 %
Rear Axle - Loaded
66 %
Transmission
Forward - 1
6.6 mile/h
Forward - 2
9.3 mile/h
Forward - 3
12.6 mile/h
Forward - 4
16.9 mile/h
Forward - 5
22.8 mile/h
Forward - 6
30.8 mile/h
Forward - 7
41.6 mile/h
Reverse
8.7 mile/h
Note
Maximum travel speeds with standard 24.00R35 (E4) tires.
Final Drives
Differential Ratio
3.64:1
Planetary Ratio
4.80:1
Total Reduction Ratio
17.49:1
Brakes
Brake Surface - Front
25.7 in²
Brake Surface - Rear
9497 in²
Brake Standards
ISO 3450:2011
Service Refill Capacities
Fuel Tank
210 gal (US)
Cooling System
43.3 gal (US)
Crankcase
24 gal (US)
Differential - Final Drives
37 gal (US)
Steering Tank
9.5 gal (US)
Steering System - Including Tank
14.3 gal (US)
Brake/Hoist Hydraulic Tank
46.5 gal (US)
Brake Hoist System
85 gal (US)
Torque Converter - Transmission System - HRC
18.5 gal (US)
Body Hoists
Pump Flow - High Idle
118 gpm
Relief Valve Setting - Raise
2502 psi
Relief Valve Setting - Lower
500 psi
Body Raise Time - High Idle
9.5 s
Body Lower Time - Float
12.5 s
Body Power Down - High Idle
14 s
Suspension
Empty Loaded Cylinder Stroke Front
9.2 in
Empty Loaded Cylinder Stroke Rear
5.8 in
Rear Axle - Oscillation
8.1°
Weights - Approximate
Maximum Gross Vehicle Weight
246503 lb
Tires
Standard Tire
24.00R35 (E4)
Note (1)
Productive capabilities of the 775G truck are such that, under certain job conditions, TKPH (TMPH) capabilities of standard or optional tires could be exceeded and, therefore, limit production.
Note (2)
Caterpillar recommends the customer evaluate all job conditions and consult the tire manufacturer for proper tire selection.
ROPS
ROPS Standards
Rollover Protective Structure (ROPS) for cab offered by Caterpillar meets ISO 3471:2008 ROPS criteria.
FOPS Standards
Falling Objects Protective Structure (FOPS) meets ISO 3449:2005 Level II FOPS criteria.
Sound
Sound Standards (1)
The operator Equivalent Sound Pressure Level (Leq) is 73 dB(A) when SAE J1166 FEB2008 is used to measure the value for an enclosed cab. This is a work cycle sound exposure level. The cab was properly installed and maintained. The test was conducted with t
Sound Standards (2)
Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.
Sound Standards (3)
The machine sound power level is 114 dB(A), measured according to the test procedures and conditions specified in ISO 6395:2008 for the standard machine configuration. The measurement was conducted at 70% of the maximum engine cooling fan speed.
Steering
Steering Standards
ISO 5010:2007
Steer Angle
31 °
Turning Circle - Clearance Diameter
82 ft
Turning Diameter - Front
72.2 ft
Sustainability
Recyclability
98%
Standard Equipment
Note
Standard and optional equipment may vary. Consult your Cat dealer for details.
Power Train
Cat C27 Tier 4/Stage V compliant diesel engine: – Air cleaner with precleaner (2) – Air-To-Air Aftercooler (ATAAC) – Electric start – Engine idle shutdown – Ether starting aid – Exhaust muffler – NGMR radiator
For Tier 4 regions only (U.S./Canada): – Aftertreatment system
Service center containing: – Battery jump start – Breakers with spare fuses – Lockout switch – Ports, ET, and VIMS – Service lockout switch (power without engine start)
Technology Products
Economy Modes, standard and adaptive
Product Link, cellular or satellite
Traction Control System (TCS)
Truck Production Management System
Vital Information Management System (VIMS)
Operator Environment
Advisor display: – Air cleaner service indicator – Fluid level monitoring – Fuel level monitoring – Display languages (market based)
Air conditioning/heat
Automatic temperature control
Ashtray and cigarette lighter
Coat hook
Cup holders (4)
Diagnostic connection port, 24V
Entertainment radio ready: – 5 amp converter – Speakers – Antenna – Wiring harness
Foot rest
Gauges/indicators: – Brake oil temperature gauge – Coolant temperature gauge – Engine overspeed indicator – Fuel level – Hour meter – Speedometer with odometer – Tachometer – Transmission gear indicator
Hoist shift lever with integrated fingerprint control
Seat belt reminder system: Seat belt alert and Seat belt inhibit