Home / Equipment / Caterpillar Machines / Motor Graders / 12M Motor Grader
Caterpillar 12M Motor Grader
Caterpillar 12M Motor GraderThe 12M delivers multiple technological breakthroughs to give you the best return on your investment. |  |  |
|
|
|
| Base Power (all gears) Net | 158 hp / 118 kW |
|
| Engine Model | Cat® C6.6 ACERT™ VHP |
|
| Displacement | 403 in3 / 6.6 L |
|
| Bore | 4.13 in / 105 mm |
|
| Stroke | 4.92 in / 125 mm |
|
| Speed @ rated power | 2000 RPM |
|
| Number of cylinders | 6 |
|
| Derating altitude | 11500 ft / 3505 m |
|
| Std - Fan speed - max | 1150 RPM |
|
| Std - Fan speed - min | 550 RPM |
|
| Std - Ambient Capability | 109 ° F / 43 ° C |
|
| Hi Ambient - Fan speed - max | 1650 RPM |
|
| Hi Ambient - Fan speed - min | 550 RPM |
|
| Hi Ambient Capability | 122 ° F / 50 ° C |
|
|
|
| Gross Vehicle Weight - base | 33064 lb / 14998 kg |
|
| Gross Vehicle Weight, max | 44690 lb / 20271 kg |
|
| Gross Vehicle Wt, max - front axle | 15954 lb / 7237 kg |
|
| Gross Vehicle Wt, max - rear axle | 48736 lb / 13034 kg |
|
| Gross Vehicle Wt, base - front axle | 9919 lb / 4499 kg |
|
| Gross Vehicle Wt, base - rear axle | 23145 lb / 10498 kg |
|
|
|
| Blade width | 12 ft / 3.7 m |
|
| Moldboard - height | 24 in / 609.6 mm |
|
| Moldboard - thickness | .87 in / 22 mm |
|
| Arc radius | 16.3 in / 413 mm |
|
| Throat clearance | 4.88 in / 124 mm |
|
| Cutting edge - width | 6 in / 152.4 mm |
|
| Cutting edge - thickness | .6 in / 16 mm |
|
| End Bit - width | 6 in / 152.4 mm |
|
| End Bit - thickness | .6 in / 16 mm |
|
| Blade Pull - base GVW | 20830 lb / 9448 kg |
|
| Blade Pull - max GVW | 25862 lb / 11731 kg |
|
| Down Pressure - base GVW | 17566 lb / 7968 kg |
|
| Down Pressure - max GVW | 28254 lb / 12816 kg |
|
|
|
| Drawbar - thickness | .4 in / 9.5 mm |
|
| Drawbar - yoke bar thickness | .75 in / 19.1 mm |
|
| Drawbar - width | 3 in / 76.2 mm |
|
| Circle - diameter | 60.2 in / 1530 mm |
|
| Circle - blade beam thickness | 1.4 in / 35 mm |
|
| Drawbar - height | 6 in / 152 mm |
|
| Front axle - height to center | 22.5 in / 572 mm |
|
| Front axle - wheel lean, left/right | 18° |
|
| Front axle - total oscillation per side | 32° |
|
|
|
| Top Speed - Fwd. | 27.7 mph / 44.5 km/h |
|
| Top Speed - Rev. | 23.5 mph / 37.8 km/h |
|
| Turning radius, outside front tires | 24.5 ft / 7.46 m |
|
| Steering range - left/right | 47.5° |
|
| Articulation angle - left/right | 20° |
|
| Fwd. 1st | 2.4 mph / 3.9 km/h |
|
| Fwd. 2nd | 3.3 mph / 5.3 km/h |
|
| Fwd. 3rd | 4.75 mph / 7.6 km/h |
|
| Fwd. 4th | 6.5 mph / 10.5 km/h |
|
| Fwd. 5th | 10.2 mph / 16.4 km/h |
|
| Fwd. 6th | 13.8 mph / 22.2 km/h |
|
| Fwd. 7th | 19 mph / 30.6 km/h |
|
| Fwd. 8th | 27.7 mph / 44.5 km/h |
|
| Rev. 1st | 2 mph / 3.3 km/h |
|
| Rev. 2nd | 3.8 mph / 6.2 km/h |
|
| Rev. 3rd | 5.6 mph / 8.9 km/h |
|
| Rev. 4th | 8.6 mph / 13.9 km/h |
|
| Rev. 5th | 16.1 mph / 26 km/h |
|
| Rev. 6th | 23.5 mph / 37.8 km/h |
|
|
|
| Fuel Capacity | 90 gal / 341 L |
|
| Cooling system | 10.4 gal / 40 L |
|
| Hydraulic system - tank | 16 gal / 60 L |
|
| Engine Oil | 4.1 gal / 15.5 L |
|
| Trans./Diff./Final Drives | 13.2 gal / 50 L |
|
| Tandem housing (each) | 16.9 gal / 61 L |
|
| Front wheel spindle bearing housing | .1 gal / .5 L |
|
| Circle drive housing | 1.8 gal / 7 L |
|
|
|
| Forward/Reverse Gears | 8 Fwd / 6 Rev |
|
| Transmission | Direct drive, power shift, countershaft |
|
| Brakes - Service | Multiple oil-disc |
|
| Brakes - Service, surface area | 3565 in2 / 23000 cm2 |
|
| Brakes - Parking | Multiple oil disc |
|
| Brakes - Secondary | Dual circuit control system |
|
|
|
| Circuit type | Electro-hydraulic closed center, load sensing, |
|
| Pump type | Variable piston |
|
| Pump output | 51 gal/min / 193 L/min |
|
| Maximum system pressure | 3500 psi / 24100 kPa |
|
| Standby Pressure | 450 psi / 3100 kPa |
|
|
|
| Circle centershift - right | 25.8 in / 656 mm |
|
| Circle centershift - left | 25.8 in / 656 mm |
|
| Moldboard sideshift - right | 26 in / 660 mm |
|
| Moldboard sideshift - left | 20.1 in / 510 mm |
|
| Maximum blade position angle | 90° |
|
| Blade tip range - forward | 40° |
|
| Blade tip range - backward | 5° |
|
| Maximum shoulder reach outside of tires - right | 75 in / 1905 mm |
|
| Maximum shoulder reach outside of tires - left | 68.6 in / 1742 mm |
|
| Maximum lift above ground | 16.8 in / 427 mm |
|
| Maximum depth of cut | 28.3 in / 720 mm |
|
|
|
| Penetration force | 18911 lb / 8578 kg |
|
| Pryout force | 25972 lb / 11781 kg |
|
| Machine length increase, beam raised | 39.2 in / 995 mm |
|
|
|
| Rear: Working width | 91 in / 2300 mm |
|
| Rear: Scarifier shank holders | 9 |
|
| Rear: Scarifier shank holder spacing | 10.5 in / 267 mm |
|
|
|
| Height | 19.76 in / 502 mm |
|
| Width | 6.76 in / 172 mm |
|
| Sidewall thickness - inner | .5 in / 14 mm |
|
| Sidewall thickness - outer | .6 in / 16 mm |
|
| Drive chain pitch | 1.8 in / 44.5 mm |
|
| Wheel axle spacing | 59.5 in / 1510 mm |
|
| Tandem oscillation - front up | 15° |
|
| Tandem oscillation - front down | 25° |
|
|
|
| Height - top of cab | 129 in / 3278 mm |
|
| Length - counterweight to ripper | 389.3 in / 9889 mm |
|
| Width - outside front tires | 97.7 in / 2481 mm |
|
| Length - front axle to mid tandem | 232.8 in / 5915 mm |
|
| Length - front tire to rear of machine | 334.1 in / 8488 mm |
|
| Length - front axle to moldboard | 98.85 in / 2511 mm |
|
| Length - between tandem axles | 59.5 in / 1511 mm |
|
| Width - outside rear tires | 97.7 in / 2481 mm |
|
| Width - tire center lines | 84.1 in / 2136 mm |
|
| Height - front axle center | 22.5 in / 572 mm |
|
| Height to exhaust stack | 112.4 in / 2855 mm |
|
| Height to top of cylinders | 113.7 in / 2890 mm |
|
| Ground clearance at rear axle | 13.6 in / 347 mm |
|
